The main purpose of using the suspension system in vehicles is to prevent the road disturbance from being transmitted to the passengers. Therefore, a precise controller should be designed to improve the performances of suspension system. This paper presents a modeling and control of the nonlinear full vehicle active suspension system with passenger seat utilizing Fuzzy Model Reference Learning Control (FMRLC) technique. The components of the suspension system are: damper, spring and actuator, all of those components have nonlinear behavior, so that, nonlinear forces that are generated by those components should be taken into account when designed the control system. The designed controller consumes high power so that when the control system is used, the vehicle will consume high amount of fuel. It notes that, when vehicle is driven on a rough road; there will be a shock between the sprung mass and the unsprung mass. This mechanical power dissipates and converts into heat power by a damper. In this paper, the wasted power has reclaimed in a proper way by using electromagnetic actuator. The electromagnetic actuator converts the mechanical power into electrical power which can be used to drive the control system. Therefore, overall power consumption demand for the vehicle can be reduced. When the electromagnetic actuator is used three main advantages can be obtained: firstly, fuel consumption by the vehicle is decreased, secondly, the harmful emission is decreases, therefore, our environment is protected, and thirdly, the performance of the suspension system is improved as shown in the obtained results.
The objective of this paper is to design an efficient control scheme for car suspension system. The purpose of suspension system in vehicles is to get more comfortable riding and good handling with road vibrations. A nonlinear hydraulic actuator is connected to passive suspension system in parallel with damper. The Particles Swarm Optimization is used to tune a PID controller for active suspension system. The designed controller is applied for quarter car suspension system and result is compared with passive suspension system model and input road profile. Simulation results show good performance for the designed controller I. I NTRODUCTION Suspensions systems can be classified into three types are (passive, simi active and active). Figs. 1, 2 and 3 below shows the three types of Quarter car suspension system and hydraulic actuator position in each type.[1] Fig. 1 Passive Quarter Car Model Fig. 2 Simi-Active Quarter Car Model Fig. 3 Active Quarter Car Model In passive suspension systems the main parts are springs and hydraulic dumpers. The main job of these dumpers is to decrease the road profile and vibration effects into driver and passenger’s cabin. In active suspension system there are three parts under spring mass (body of car), spring, dumper and hydraulic actuator are connected in parallel. In this paper an additional parts is added to passive suspension system in parallel with springs and dumpers called a hydraulic actuator to get an active suspension system. This hydraulic actuator is a nonlinear part and it is controlled by spool valve. The mechanism of this actuator is to decrease the road profile and vibration from passive suspension system to get more comfortable riding. By using PID controller trained by Particle Swarm Optimization (PSO) to find optimal values of proportional, divertive and Quarter Car Active Suspension System Control Using PID Controller tuned by PSO Wissam H. Al-Mutar Turki Y. Abdalla Electrical Eng. Computer Eng. University of Basrah University of Basrah Basrah. Iraq. Basrah. Iraq. Spring Mass Unpring Mass K Kt C Ct Spring Mass Unpring K K C C Spring Mass Unpring Mass K Kt C F Ct اﻟﻤﺠﻠﺔ اﻟﻌﺮاﻗﻴﺔ ﻟﻠﻬﻨﺪﺳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ واﻻﻟﻜﺘﺮوﻧﻴﺔ Iraq J. Electrical and Electronic Engineering ﻡﺠﻠﺪ 11 ، اﻟﻌﺪد 2 ، 2015 Vol.11 No.2 , 2015 Active suspension, PSO, PID controller, quarter car
According to the growing interest in the soft robotics research field, where various industrial and medical applications have been developed by employing soft robots. Our focus in this paper will be the Pneumatic Muscle Actuator (PMA), which is the heart of the soft robot. Achieving an accurate control method to adjust the actuator length to a predefined set point is a very difficult problem because of the hysteresis and nonlinearity behaviors of the PMA. So the construction and control of a 30 cm soft contractor pneumatic muscle actuator (SCPMA) were done here, and by using different strategies such as the PID controller, Bang-Bang controller, Neural network controller, and Fuzzy controller, to adjust the length of the (SCPMA) between 30 cm and 24 cm by utilizing the amount of air coming from the air compressor. All of these strategies will be theoretically implemented using the MATLAB/Simulink package. Also, the performance of these control systems will be compared with respect to the time-domain characteristics and the root mean square error (RMSE). As a result, the controller performance accuracy and robustness ranged from one controller to another, and we found that the fuzzy logic controller was one of the best strategies used here according to the simplicity of the implementation and the very accurate response obtained from this method.
Rehabilitation robots have become one of the main technical instruments that Treat disorder patients in the biomedical engineering field. The robotic glove for the rehabilitation is basically made of specialized materials which can be designed to help the post-stroke patients. In this paper, a review of the different types of robotic glove for Rehabilitation have been discussed and summarized. This study reviews a different mechanical system of robotic gloves in previous years. The selected studies have been classified into four types according to the Mechanical Design: The first type is a tendon-driven robotic glove. The second type of robotic glove works with a soft actuator as a pneumatic which is operated by air pressure that passes through a plastic pipe, pressure valves, and air compressor. The third type is the exoskeleton robotic gloves this type consists of a wearable mechanical design that can used a finger-based sensor to measure grip strength or is used in interactive video applications. And the fourth type is the robotic glove with a liner actuator this type consists of a tape placed on the fingers and connected to linear actuators to open and close the fingers during the rehabilitation process.
This paper presents a simple and fast design and implementation for a soft robot arm. The proposed continuum arm has been built by a single self-bending contraction actuator (SBCA) with two-fingers soft gripper. Because of the valuable advantages of the pneumatic artificial muscle (PAM), this continuum arm provides a high degree of safety to individuals. The proposed soft robot arm has a bending behaviour of more 180° at 3.5 kg, while, its weight is 0.7 kg. Moreover, it is designed to assist the people by reducing the number of backbends and that leads to a decrease in the possibility of lower back pain.
Soft robots, which are often considered safer than rigid robots when interacting with humans due to the reduced risk of injury, have found utility in various medical and industrial fields. Pneumatic artificial muscles (PAMs), one of the most widely used soft actuators, have proven their efficiency in numerous applications, including prosthetic and rehabilitation robots. PAMs are lightweight, responsive, precise, and capable of delivering a high force-to-weight ratio. Their structure comprises a flexible, inflatable membrane reinforced with fibrous twine and fitted with gas-sealing fittings. For the optimal design and integration of these into control systems, it is crucial to develop mathematical models that accurately represent their functioning mechanisms. This paper introduces a general concept of PAM’s construction, its various types, and operational mechanisms, along with its key benefits and drawbacks, and also reviews the most common modeling techniques for PAM representation. Most models are grounded in PAM architecture, aiming to calculate the actuator’s force across its full axis by correlating pressure, length, and other parameters that influence actuator strength.
Soft robotics is a modern technique that allows robots to have more capabilities than conventional rigid robots. Pneumatic Muscle Actuators (PMAs), also known as McKibben actuators, are an example of soft actuators. This research covered the design and production of a pneumatic robot end effector. Smooth, elastic, flexible, and soft qualities materials have contributed to the creation of Soft Robot End-Effector (SREE). To give SREE compliance, it needs to handle delicate objects while allowing it to adapt to its surroundings safely. The research focuses on the variable stiffness SREE’s inspiration design, construction, and manufacturing. As a result, a new four-fingered variable stiffness soft robot end effector was created. SREE has been designed using two types of PMAs: Contractor PMAs (CPMAs) and Extensor PMAs (EPMAs). Through tendons and Contractor PMAs, fingers can close and open. SREE was tested and put into practice to handle various object types. The innovative movement of the suggested SREE allows it to grip with only two fingers and open and close its grasp with all of its fingers.
The reluctance of industry to allow wireless paths to be incorporated in process control loops has limited the potential applications and benefits of wireless systems. The challenge is to maintain the performance of a control loop, which is degraded by slow data rates and delays in a wireless path. To overcome these challenges, this paper presents an application–level design for a wireless sensor/actuator network (WSAN) based on the “automated architecture”. The resulting WSAN system is used in the developing of a wireless distributed control system (WDCS). The implementation of our wireless system involves the building of a wireless sensor network (WSN) for data acquisition and controller area network (CAN) protocol fieldbus system for plant actuation. The sensor/actuator system is controlled by an intelligent digital control algorithm that involves a controller developed with velocity PID- like Fuzzy Neural Petri Net (FNPN) system. This control system satisfies two important real-time requirements: bumpless transfer and anti-windup, which are needed when manual/auto operating aspect is adopted in the system. The intelligent controller is learned by a learning algorithm based on back-propagation. The concept of petri net is used in the development of FNN to get a correlation between the error at the input of the controller and the number of rules of the fuzzy-neural controller leading to a reduction in the number of active rules. The resultant controller is called robust fuzzy neural petri net (RFNPN) controller which is created as a software model developed with MATLAB. The developed concepts were evaluated through simulations as well validated by real-time experiments that used a plant system with a water bath to satisfy a temperature control. The effect of disturbance is also studied to prove the system's robustness.
Some engineering applications requires constant engine speed such as power generators, production lines ..etc. The current paper focuses on adding a new closed loop based on engine torque. Load cells can be used to measure the torque of load applied , the electrical signal is properly handled to manipulate a special fuel actuator to compensate for the reduction in engine speed. The speed loop still acts as the most outer closed loop. This method leads to rapid speed compensation and lead control action.
A Programmable logic controller (PLC) uses the digital logic circuits and their operating concepts in its hardware structure and its programming instructions and algorithms. Therefore, the deep understanding of these two items is staple for the development of control applications using the PLC. This target is only possible through the practical sensing of the various components or instructions of these two items and their applications. In this work, a user-friendly and re-configurable ladder, digital logic learning and application development design and testing platform has been designed and implemented using a Programmable Logic Controller (PLC), Human Machine Interface panel (HMI), four magnetic contactors, one Single-phase power line controller and one Variable Frequency Drive (VFD) unit. The PLC role is to implement the ladder and digital logic functions. The HMI role is to establish the virtual circuit wiring and also to drive and monitor the developed application in real time mode of application. The magnetic contactors are to play the role of industrial field actuators or to link the developed application control circuit to another field actuator like three phase induction motor. The Single -phase power line controller is to support an application like that of the soft starter. The VFD is to support induction motor driven applications like that of cut-to-length process in which steel coils are uncoiled and passed through cutting blade to be cut into required lengths. The proposed platform has been tested through the development of 14 application examples. The test results proved the validity of the proposed platform.
This paper focuses on the vibration suppression of a half-car model by using a modified PID controller. Mostly, car vibrations could result from some road disturbances, such as bumps or potholes transmitted to a car body. The proposed controller consists of three main components as in the case of the conventional PID controller which are (Proportional, Integral, and Derivative) but the difference is in the positions of these components in the control loop system. Initially, a linear half-car suspension system is modeled in two forms passive and active, the activation process occurred using a controlled hydraulic actuator. Thereafter, the two systems have been simulated using MATLAB/Simulink software in order to demonstrate the dynamic response. A comparison between conventional and modified PID controllers has been carried out. The resulting dynamic response of the half-car model obtained from the simulation process was improved when using a modified PID controller compared with the conventional PID controller. Moreover, the efficiency and performance of the half-car model suspension have been significantly enhanced by using the proposed controller. Thus, achieving high vehicle stability and ride comfort.
This work presents a Fuzzy based adaptive Sliding Mode Control scheme to deal with control problem of full vehicle active suspension system and take into consideration the nonlinearities of the spring and damper, unmodeled dynamics as well as the external disturbances. The control law of fuzzy based adaptive Sliding Mode Control scheme will update the parameters of fuzzy sliding mode control by using the stability analysis of Lyapunov criteria such that the convergence in finite time and the stability of the closed loop are ensured. The proposed control scheme consists of four similar subsystems used for the four sides of the vehicle. The sub control scheme contains two loops, the outer loop is built using sliding mode controller with fuzzy estimator to approximate and estimate the unknown parameters in the system. In the inner loop, a controller of type Fractional Order PID (FOPID) is utilized to create the required actuator force. All parameters in the four sub control schemes are optimized utilizing Artificial Bee Colony (ABC) algorithm in order to improve the performance. The results indicate the effectiveness and good achievement of the proposed controller in providing the best ability to limit the vibration with good robustness properties in comparison with passive suspension system and using sliding mode control method. The controlled suspension system shows excellent results when it was tested with and without typical breaking and bending torques.