Soft commutation techniques have been of great interest during the last few years in power supply switching applications. The recently developed Zero-Voltage transition (ZVT) and Zero-Current transition (ZCT) pulse width modulation (PWM) technique incorporated soft-switching function into PWM converters, so that the switching losses can be reduced with minimum voltage/current stresses and circulating energy. The ZCT technique can significantly reduce the switch turn-off loss which is usually the dominant switching loss in high-power applications. In this paper the steady state analysis and design of the ZCT PWM boost converter are introduced. Control and drive circuit have been designed to drive a 100 Watt ZCT PWM boost converter to experimentally investigate its features and characteristics.
The conventional multilevel inverter (MLI) is divided into three types: diode clamped MLI, cascade H Bridge MLI and flying capacitor MLI. The main disadvantage of these types is the higher required number of components when the number of the levels increases and this results in more switching losses, system higher cost, more complex of control circuit as well as less accuracy. The work in this paper proposes two topologies of nonconventional diode clamping MLI three phase nine levels and eleven levels. The first proposed topology has ten switches and six diodes per phase while the second topology has nine switches and four diodes per phase. The pulse width modulation (PWM) control method is used as a control to gate switches. THD of the two proposed topologies are analyzed and calculated according different values of Modulation index (where the power loss and efficiency are obtained and plotted.
In this paper, a proposed control strategy is presented to improve the performance of the pulse width modulation (PWM) boost type rectifier when operating under different supply voltage conditions (balanced, unbalanced, and distorted three-phase supply voltages). The proposed control strategy is divided into two parts, the first part is voltage controller and the second part is current controller. In the voltage controller, Repetitive Controller (RC) is used to reduce the even order harmonics in the regulated output dc voltage so small output capacitor (filter) is used instead of large capacitor. RC also reduces the even order harmonics which appear in the reflected dc current (I MAX ), this leads to reduce the odd order harmonics which appear in the input currents. While in the current controller, Enhanced Phase Locked Loop (EPLL) technique is used to obtain sinusoidal and balanced three phases, to construct the reference currents, which are in phase with the fundamental supply voltages. Therefore, the supply-side power factor is kept close to unity. A proportional controller is used to give excellent tracking between the line and the reference currents. The complete system with the proposed control strategy are simulated using Matlab/Simulink. The results for the complete system using repetitive voltage controller are obtained and compared to the results of the system with the conventional voltage controller (Proportional-Integral (PI) controller connected in series with a Low Pass Filter (LPF)). The results with the repetitive controller show better response and stable operation in the steady state under different input voltage conditions, as well as in the transient response under changing the load condition. — Enhanced Phase Locked Loop,Repetitive Controller,Three-Phase PWM Boost Rectifier, Proportional-Integral controller. I. INTRODUCTION The boost type PWM rectifier has been increasingly employed in recent years since it offers the possibility of a low distortion line current withnear unity power factor for any load condition. Another advantage over traditional phase-controlled thyristor rectifiers is its capability for nearly instantaneous reversal of power flow. Unfortunately, the features of the PWM boost type rectifier are fully realized only when the supply three phase input voltages are balanced. It has been shown that unbalanced input voltages cause an abnormal second order harmonic at the dc output voltage, which reflects back to the input causing third-order harmonic current to flow. Next, the third-order harmonic current causes a fourth-order harmonic voltage on the dc bus, and so on. This results in the appearance of even harmonics at the dc output and odd harmonics in the input currents. An attempt was made to reduce low order harmonics at the input and the output of the PWM Boost Type Rectifier under unbalance input voltages [1]. The authors in [2] used two synchronous reference frames: a positive- sequence current regulated by a
The paper dells with a modified experimental prototype for pulse-width modulation (PWM) sliding mode control (SMC) applied to a DC-to-DC-boost converter operated in continuous conduction mode (CCM). Experimental results show that the proposed control schme provides good voltage regulation and is suitable for common DC-to-DC conversion purposes. The prototype and its implementation are given in detail. The static and dynamic performances of the The static and dynamic performances of the experimental system are recorded. Experimental results show that the proposed control scheme provides good voltage regulation and is suitable for common DC-to-DC conversion purposes.
This paper presents a simplified control method for three-phase active power filter by calculating the required reactive and harmonics current of the load. The active power filter needs this current to correct the power factor and eliminate the generated harmonics by nonlinear loads. This method has the advantages of using only one current sensor and effectiveness in achieving the required compensation characteristics. The proposed circuit may be operate at frequencies ranging from 40 to 60 Hz, and it also responds very fast under sudden changes in the load conditions. The considered system is analyzed and a prototype is also developed and tested to demonstrate the performance of the implemented active power filter in the power factor improvement and harmonics elimination. Finally, predicted results are verified experimentally.
In medium voltage and high-power drive applications, pulse width modulation (PWM) techniques are widely used to achieve effective speed control of AC motors. In real-time, an industrial drive system requires reduced hardware complexity and low computation time. The reliability of the AC drive can be improved with the FPGA (field programmable gate array) hardware equipped with digital controllers. To improve the performance of AC drives, a new FPGA-based Wavect real-time prototype controller (Xilinx ZYNQ-7000 SoC) is used to verify the effectiveness of the controller. These advanced controllers are capable of reducing computation time and enhancing the drive performance in real- time applications. The comparative performance analysis is carried out for the most commonly used voltage source inverter (VSI)-based PWM techniques such as sinusoidal pulse width modulation (SPWM) and space vector pulse width modulation (SVPWM) for three-phase, two-level inverters. The comparative study shows the SVPWM technique utilizes DC bus voltage more effectively and produces less harmonic distortion in terms of higher output voltage, flexible control of output frequency, and reduced harmonic distortion at output voltage for motor control applications. The simulation and hardware results are verified and validated by using MATLAB/Simulink software and FPGA-based Wavect real-time controller respectively.
In this article, a comparison of innovative multilevel inverter topology with standard topologies has been conducted. The proposed single phase five level inverter topology has been used for induction heating system. This suggested design generates five voltage levels with a fewer number of power switches. This reduction in number of switches decreases the switching losses and the number of driving circuits and reduce the complexity of control circuit. It also reduces the cost and size for the filter used. Analysis and comparison has been done among the conventional topologies (neutral clamped and cascade H-bridge multilevel inverters) with the proposed inverter topology. The analysis includes the total harmonic distortion THD, efficiency and overall performance of the inverter systems. The simulation and analysis have been done using MATLAB/ SIMULINK. The results show good performance for the proposed topology in comparison with the conventional topologies.
In this article, a PD-type iterative learning control algorithm (ILC) is proposed to a nonlinear time-varying system for cases of measurement disturbances and the initial state errors. The proposed control approach uses a simple structure and has an easy implementation. The iterative learning controller was utilized to control a constant current source inverter (CSI) with pulse width modulation (PWM); subsequently the output current trajectory converged the sinusoidal reference signal and provided constant switching frequency. The learning controller's parameters were tuned using particle swarm optimization approach to get best optimal control for the system output. The tracking error limit is achieved using the convergence exploration. The proposed learning control scheme was robust against the error in initial conditions and disturbances which outcome from the system modeling inaccuracies and uncertainties. It could correct the distortion of the inverter output current waveform with less computation and less complexity. The proposed algorithm was proved mathematically and through computer simulation. The proposed optimal learning method demonstrated good performances.